MKI STANDARD COMPONENTS LIST

BODY, MOUNTED ON CHASSIS, COMPLETE WITH :
  • Doors, hinged and latched
  • Front body section, hinged and latched
  • Front body limit cable
  • Hood panel attached w/Dzus fasteners
  • Headlight access panels
  • Rear body section, hinged and latched
  • Rear body limit strap
  • Front and rear inner body panels bonded in place
  • Door limit straps
  • Door handles, as original
  • Acrylic plastic headlight covers
  • Acrylic plastic driving light covers
  • Weather seals
  • Holes for lights drilled or cut out
  • Brake and interior ventilation ducts built into body

CHASSIS - SHEET STEEL SEMi-MONOCOQUE WITH SQUARE-TUBE
SUB-FRAMES [VISUALLY CLOSE TO ORIGINAL] WITH:

  • Built in roll bar
  • Aluminum rear bulkhead panels
  • Brake and clutch pedal assembly adjustable fore and aft
  • Sheet steel cowl structure similar to original
  • Aluminum front compartment panels Installed
  • Radiator and front body mounting tubular sub-frame
  • Rear body mounting tubular sub-frame
  • Fuel tank access panels

CHASSIS
Ready with captive nuts or proper holes to accept as bolt-ins the following components:

  • Engine Hand brake handle Front and rear suspension
  • Transaxle Steering column Dashboard
  • Rack and Pinion Sway bars Pedal assembly
  • Fuel tanks Seats/adjusting tracks
  • Windshield wiper motor
  • Fluid reservoirs Horns Fuel caps
  • Battery Fuel pumps Body latches
  • Seat bottom padding and seat back.
  • Seat belts/harness
  • Shifting mechanism

BRAKING SYSTEM INCLUDES:

  • Adjustable pedal assembly
  • Dual master cylinders w/balance bar
  • Steel brake lines run and fitted to chassis
  • Brake fluid reservoir bracket
  • Brake light switch .
  • Master cylinder fill tube
  • Brake fluid reservoirs

CLUTCH SYSTEM INCLUDES:

  • Master cylinder .
  • Slave cylinder
  • Slave cylinder bracket
  • Master cylinder fill tube
  • Pedal assembly
  • Steel and flex lines [master to slave]
  • Fluid reservoir bracket
  • Clutch fluid reservoir .

COOLING SYSTEM INCLUDES:

  • Custom made aluminum crossflow radiator
  • Radiator stone guard
  • Shrouding
  • Dual electric fans
  • Coolant pipes [radiator to engine] . .
  • Fan thermostatic control switch
  • Fan manual override switch .
  • Connector hoses/clamps
  • Rubber grommets for pipes passing thru chassis

DASH BOARD, AS ORIGINAL COMPLETE WITH :

  • Gauges, Stewart Warner
    • Speedometer
    • Tachometer
    • Oil pressure
    • Water temperature
    • Oil temperature
    • Fuel level (2 gauges)
  • High beam indicator light
  • Turn indicator light
  • Cooling fan indicator light
  • Ignition indicator light
  • Ignition switch
  • Light switches
  • Fuel pump switch
  • Cooling fan override switch
  • Heater/defroster switch
  • Wiper switch
  • Fresh air control knob
  • Ventilation eyeball vents
  • Ventilation defroster vents
  • Panel light switch
  • Fuse block access panel
  • Turn signal switch

WIRING HARNESS
Complete w/fuse blocks, relays and the following:

  • Rubber grommets and hold down clips for wire harness
  • Headlights
  • Taillights
  • Signal lights
  • Driving lights
  • License plate lights
  • Horns
  • Switches [see Dashboard]

FUEL SYSTEM, INCLUDES:

  • Fuel tanks E2l custom made, foam filled, polyethelene cells
  • Fuel filler caps [2] aluminum
  • Fuel filler pipes
  • Fuel filler hoses .
  • Hose clamps .
  • Accelerator pedal assembly
  • Accelerator cable and bracket
  • Fuel level gauges
  • Fuel level sending units

INTERIOR, INCLUDES :

  • Seats, integrated into chassis, visually identical to originals, Naugahyde
  • Carpets, cut and bound w/heel pads
  • Door panels
  • Console/arm rest fully upholstered
  • Rear bulkhead covering [foam and vinyl, precut w/finished edges]
  • Tunnel cover upholstered

SHIFTING SYSTEM, INCLUDES:

  • Shifter box
  • Shifter rods
  • Shift lever
  • Shift lever boot
  • Shift lever bezel
  • Shift knob

STEERING AND SUSPENSION, INCLUDES:

  • Front upper and lower control arms-adjustable w/ball joints w/ urethane bushings
  • Cast aluminum front upright with steel ball joint inserts
  • Billet aircraft aluminum steering arms
  • Rack and pinion clevis ends
  • Tie rods w/ball joints
  • Steering wheel, center cap & medallion
  • Steering column, adjustable height, fore and aft .
  • Rear hub carrier
  • Rear upper and lower control arms and trailing links-adjustable

TRIM AND ATTACHMENTS, INCLUDES :

  • Door aero-fairings
  • Mirrors side view (2)
  • Weather seals for doors, rear body
  • Rubber grommets for water and oil temperature lines, wiring harness, shifting rods, brake lines water pipes etc
  • Louvered vent panel for top of rear body
  • Louvered vent panels for rear of body [2] .
  • Hand brake cables
  • Fresh air duct hoses
  • Fresh air control cables
  • Ventilation/defroster grille (top of dash)
  • Dashboard adjustable swivel vents (2)
  • Rooftop exhaust vent w/water trap & drain hose

WINDOWS, INCLUDES:

  • Windshield
  • Vent windows, swing out
  • Acrylic plastic door windows w/stainless steel screws
  • Acrylic plastic rear window w/stainless steel screws
  • Safety glass intermediate rear window w/gasket
  • Windshield wiper arm & blade

VENTILATION SYSTEM

  • Fresh air duct hoses
  • Fresh air control cables
  • Ventilation/defroster grille  on top of dash
  • Dashboard adjustable swivel vents [2] .
  • Rooftop exhaust vent w/water trap and drain hose
  • Vent windows

Also included is an illustrated, fully detailed assembly manual, complete with a list of part numbers and sources for all the minor parts necessary to build a complete car, and which are to be supplied, either new or used, by the customer such as radIator hoses, fan belts, windshield wiper motor, arms, blades, etc. Every part necessary to build a complete car is accounted for either in the standard kit or the parts source list.